Mr. Heater Propane Garage Heater — 75,000 BTU, Mod,
November 18, 2008
By MUNSTER57 from NORTH, IDAHO
"This is one great heater, I put in my new 24 x 30 x 10 shop. Heats it up fast. easy to install, and very quiet. Right now I run it on a 20# propane tank until I get it hooked up to a much larger tank. highly recomended. I put a programable t-stat on it with a fan only option on it. works great for moving air without heat on. Way nicer and cleaner than my old wood heater I had."
What is your level of technical expertise? Home Handyman
2 of 2 people found this review helpful.
Great Heater, reasonable price,
November 2, 2009
By coldblooded5 from Seaford, Delaware
"I cannot tell you how happy I am with my new Mr Heater Propane Garage heater. I work out of 3/4ths of a large converted two car garage in which I have an intaglio (hand pulled etchings) studio. Last winter I suffered endlessly trying to heat the place with two large electric heaters. Not any more. Two people were able to easily install my Mr Heater by hanging it from the ceiling. The instructions were clear, access was good, and once up and running it heated almost instantly and was so proficient I had to turn it down. There are no alarming smells and it is reasonably quiet. I don't think you can expect more from a product and I am prepared to be its happy owner for many years to come."
What is your level of technical expertise? Beginner
Super Quiet and East to Install,
November 2, 2009
By motherslawn from York, Maine
"Bought this for my barn, Installed it in less that 2 hrs hanging from ceiling.
I liked the fact it was electronic start, Unit has been in service for 3 years with NO issues, starts everytime and is very quiet for what it is."
What is your level of technical expertise? Home Handyman
Great heater for the price,
July 20, 2009
By HARVMAN from central South Dakota
"I had this heater installed and ducted in a couple of hours. It is in a 30 X 70 building that is insulated. I use the building usually one night during the week and all day on Sat and Sun. I keep the thermostat at 45 and even on the coldest days it only takes about 45 minutes to get the building up to 65. I have it hooked to a 500 gallon tank and I ran it from the end of november to around the first of april and used approx. 40 percent of the tank and we had a very cold winter."
What is your level of technical expertise? Home Handyman
1 of 1 people found this review helpful.
I got it working correctly, finally.,
March 24, 2009
By daveinwash from Western Washington State
"I've had this heater for over a year. It worked great for a few weeks, then failed to light. I was getting the "two flash light". I flicked power on & off, tried again aand it lit off correctly. Then, a month or two later, it failed again. I checked safeties & traced power. It had blown the low-voltage transformer. I removed & tested it again, yes, the transformer was dead. Luckily, I had a spare in my shop. I hooked that one up (a better transformer with a higher VA rating) & tested the system. Now, so far, it is powering and firing correctly. The heater was fairly easy to hook up. I purchased the flue kit, & ran a t-stat to the other side of the room, next to the enrty door (I can turn it on then entering the bldg). I ran a 120v 20A circuit to a 4x4 box on the wall, & ran flex to the unit. I also ran a gas line in the wall to outside my shop, running to a 120lb tank. My shop is 24X36X9 and insulated fairly good. This heater heats my shop from the low 30's into the 60's within 15 minutes. It really cranks out the heat (and empties my propane). I really would have to caution some about this unit, though maybe mine was just a lemon. I called Mr. Heater, & they sent me a new transformer. I do repairs like this for a living, but maybe others would have difficulty. I really would prefer to not have to repair fairly new items like this."
What is your level of technical expertise? Home Handyman
1 of 1 people found this review helpful.
Mr. Heater LP — 75,000 BTU,
March 16, 2009
"Easy to install, fired right up on a Honeywell programmable thermostat and works great. Might be a bit undersize for my situation (well insulated 30 X 25 shop w 12' ceiling) but it kept the shop at 50o easily even in -20oF Minnesota winter and warms up to 70oF quickly. I did have to put in a ceiling fan to help circulation. Sizing is not a Northern deal though, its on the Mr Heater website, they might be a bit optimistic for the northern states."
What is your level of technical expertise? Home Handyman
Small package, BIG HEAT!,
February 12, 2009
"I waited long enough and purchased the 75,000btu unit after a lot of comparing. I can say that it does the job and does it well. Hookup was simple once the heater was in place. I did a test fire at floor level with a small tank and it worked flawlessly. I also purchase the themostat which I highly recommend getting.
I have a 24x30 block garage attatched to the house with 12' ceilings exposed. The heater brought the temp from 35° to 65° in about 30min. The fan is very quiet compared to a kerosene floor tube heater. I can still think when its on. Once the directional blades were pointed in a direction that would benefit the work area, it keeps the area warm and doesn't cycle all that much.
The workmanship is very good and instructions were adequate for even the novice home owner. The important part is making sure where you want it and trying to estimate how it will work when installed. If you can do a temporary install to direct air flow, this would be a huge benefit for the final installation.
Another nice feature is the fact you can wire the control to run just the fan in summer months. I plan to do this later this year.
The unit is not too heavy but two people should do the install for safety."
What is your level of technical expertise? Professional
Heater nice. Installation was work!,
January 8, 2009
"Ordered the propane model to put up in a Morton Building workshop. Package arrived quickly with minimal damage to outside cardboard box. Nice unit and fairly easy to lift (I am 6' 190 lbs. average jock) but recommend two people to lift in place on ladder or other device.
Things to consider for installation: Installed two joist between trusses in the attic to hang the unit from (time consuming). Venting horizontal is easier but I perfer vertical. Think this process out. This unit requires a 4" exhaust vent. I went through a metal roof and used a Dektite on 4" double wall exhaust pipe. Make sure you have the appropriate tools, fasteners and sealers before starting this part of the project. Hooking the exhaust vent to the unit should be well planned too. It is not easy and you should have the exhaust vent pieces you plan to use to take some rough measurements prior to fit up. I hung the unit using threaded rod on C channel so I could adjust the unit up or down, side to side, and back to front (I used 19" center to center from side to side, could use 20" too). The brackets in the kit require a small amount of grinding to avoid the strain relief on the blower fan and if you use the top 1/2" knockout on the back of the unit for electrical connections. Electrical connections are easy. The unit has two 1/2" knockouts on back for electrical connections. I used 16-3 cord for power and 18-2 (solid) for the thermostat. I have it on a 15 amp circuit breaker. Use a strain relief for the power cord. The gas pipe connection is 1/2" female. I already had propane gas pipe in the shop. I used various elbows, cross, and 1/2" pipe lengths for initial plumbing. A union was used for the final connection. Exhaust vent was connected first and then the gas pipe was fitted. It is easier to make adjustments to the gas pipe than the exhaust venting. A plumb bob is handy during the entire project. Once all connections were checked, the unit powered up, the appropriate green light flashed on the circuit board and the unit fired right up.
The only problem with the heater involved the two top burners were allowing flame to reach and burn the section between the heat tubes. A call to technical support (30 to 45 minute wait on a Monday) stated to pinch the two pieces of metal that form the burner closer together in the area involved which solved the problem. This would not please the average joe. It involved removing 6 screws that hold the panel that the circuit board is on and 4 screws that hold the two burners in place. It took me two times to get it right. I didn't mind as I like to tinker and I have an above average selection of tools.
The unit is quiet for a forced air heater. It works great and heats up my 1800 square foot workshop quickly. It took two weeks of various evenings and weekends at a leisurely pace to get it installed. This review is being written two weeks after installation so no comments on longevity. Good luck!"
What is your level of technical expertise? Home Handyman