Northern Tool Ratings and Reviews

Customer Reviews for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"

"Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"

Item# 233510
"Hilliard Extreme-Duty clutches are ideal for the everyday demands of go-karts and youth-model snowmobiles. Thermodynamically designed clutch shoe increases the clutch's capacity to absorb heat without damaging the clutch springs, thereby providing a longer service life, even in the most demanding applications. For use with engines up to 13 HP. No warranty. Returns on unused product only. U.S.A. Overload Protection Yes, Engagement Speed RPM 1,800, Bore Diameter in. 1, Keyway in. 1/4, Engine Up to 13 HP, Pulley Diameter in. 3, Application Pulley. Bi-directional operation Load-free starting Overload protection Easy to install Integral key design Easy-to-change springs Tolerates excessive heat generated by inexperienced riders, riding with one foot on brake, riding in soft dirt and tall grass, and frequent starts and stops Will work with either 1/2in.W 'A' or 5/8in.W 'B' belt"
Average Customer Rating:
5 out of 5
5
 out of 
5
(6 Reviews) 6
Open Ratings Snapshot
Rating Summary (6 reviews)
5 stars
6
4 stars
0
3 stars
0
2 stars
0
1 star
0
6 of 6(100%)would recommend this product to a friend.
Customer Questions & Answers:
9 Questions | 11 Answers
Customer Reviews for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Review 1 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

great clutch

,
July 6, 2015
By lorax63
from vt
" I put this clutch on my saw mill and it restored the torque my saw had when it was new. the pulley wheels roll freely when the motor is at idle "
Describe Yourself: Professional
0points
0out of 0found this review helpful.
Thank you! You have successfully submitted a comment for this review.
Review 2 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

Hillard extreme clutch

,
March 16, 2015
By toshiba
from Pennsylvania
" This is a very well designed clutch and heavy duty . I used it on a Chipper with an 8 horse motor drive . Never heats up or slips. "
Describe Yourself: Home Handyman
0points
0out of 0found this review helpful.
Thank you! You have successfully submitted a comment for this review.
Review 3 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

strong lockup

,
February 4, 2014
By roperizer
from Goodhue Mn
" I have this on my rider go kart contraption and it works awesome I hit the gas and it'll spin the 22in 4Wheeler tires no problems as of yet "
Describe Yourself: Home Handyman
+1point
1out of 1found this review helpful.
Thank you! You have successfully submitted a comment for this review.
Review 4 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

Belt Clutch

,
February 4, 2014
By tinbox
from Beaumont,Tx.
" Great clutch - holds up well for hard pulling of a Go Kart of 11 HP engine ! Very Good Buy ! If you need a clutch than can stand hard pulling in ruff areas or down the strip this one holds up better than others I have used ! If it ever wears out I will get another ! "
Describe Yourself: Professional
0points
0out of 0found this review helpful.
Thank you! You have successfully submitted a comment for this review.
Review 5 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

Hilliard Extreme-Duty Clutch

,
January 19, 2012
By carpetdigger
from Tulsa, OK
" I purchased this clutch for a go kart that I had modified with an engine bigger than original. I also needed a bigger bore clutch because the old engines output shaft was 3/4" and the new engine had a 1" shaft. This was about the best price + best quality I could hope for (I could actually "drift" the go kart now) thanks Northern Tool. "
Describe Yourself: Professional
+4points
7out of 10found this review helpful.
Thank you! You have successfully submitted a comment for this review.
Review 6 for "Hilliard Extreme-Duty Clutch - 1in. Bore, 3.0in. Pulley O.D., For 1/2in.W 'A' Belts and 5/8in.W 'B' Belts"
Overall Rating:
5 / 5
5 / 5

Hilliard Extreme Duty Clutch

,
June 1, 2010
By Redfish
from Houston, Texas
" Put this clutch on vecihile that was made for a parade. Vecihile weighs about 800 lbs. The clutch is on a 21 HP v-2 attached to 6 speed garden tracto tranny ; clutch worked flawlessy and moves the ' car ' right up to 10 mph no problem. parade route is about 8 miles.
Plan on using this type of clutch on the next ' made ' ' car '
Would recomend this clutch to any one.
"
Describe Yourself: Home Handyman
+15points
15out of 15found this review helpful.
Thank you! You have successfully submitted a comment for this review.