Northern Tool Ratings and Reviews
Shop Now At Northern Tool

Customer Reviews for "Please see replacement item# 48643. FREE SHIPPING - Hobart AirForce 700i Plasma Cutter - 230V, 40 Amps, Model #500546"

This product is no longer available. Continue shopping at Northern Tool.

"Please see replacement item# 48643. FREE SHIPPING - Hobart AirForce 700i Plasma Cutter - 230V, 40 Amps, Model #500546"

Item# 628573
"The Hobart Air Force 700i Plasma Cutter is an economical plasma cutting system for all conductive metals. It can cut mild steel up to 7/8in. This portable unit features a lightweight, powerful inverter design and an ergonomic trigger safety, with more efficient air consumption and economically priced consumables. Plasma cutters cut faster and more precise with a thinner kerf and less slag than cutting with oxy fuel. A smaller heat-affected zone also causes less warping. And you'll never have gas pressure settings, flame tuning, metal preheating, or gas cylinders or refills to worry about. Features Hobart's 5/3/1 industrial warranty protection. Power Cord ft. 10, Clamp Cable Length ft. 16 1/2, Plasma Gas Flow/Pressure 4.8 CFM 136 L/min at 90-120 PSI 621 - 827 kPA recommended, Dimensions L x W x H in. 14 1/4 x 8 1/4 x 11 1/4, Cutting Thickness in. Up to 7/8-in. mild steel, Amps 40, Duty Cycle 50 @ 40A, Pilot Arc Yes, Volts 230, Cart No. Features 16 1/2ft. torch - designed for increased comfort with an ergonomic trigger safety, more efficient cooling and economical replacement cutting tips Wind Tunnel Technology prevents abrasive dust and particles from damaging internal components Fan-On-Demand Cooling system operates only when needed, reducing power consumption and contaminants drawn into the machine Power factor correction PFC circuitry draws up to 30 less amperage for the same cutting range as compared to the competition. PFC expands operator's work area via extension cord, while minimizing nuisance circuit breaker trips caused by voltage drops LVC line voltage compensation provides peak performance power under variable input voltage conditions 15 for steady and cleaner-ending cuts Internal gas/air filter and regulator controls amount of usage and flow of air or gas Starts without high frequency, protecting the unit by not interfering with or damaging controls or computers Diagnostic LED lights for quick troubleshooting of pressure, power and cup situations Cable management strap secures torch, work cable and power cord to make transporting easy and convenient Postflow cooling circuit extends life of consumables and torch by cooling them with postflow air after trigger is released Compatible with engine-driven welders capable of cutting 3/8-5/8 in. mild steel when powered by an engine-driven welder with a 240 V generator power outlet of 8 kW or more Hobart 5/3/1 limited warranty Hobart's 5/3/1 Industrial Warranty Five-year warranty on transformers, stabilizers and generators three years on electronics drive motors, rectifiers and one year on guns MIG and plasma torches"
Average Customer Rating:
4 out of 5
4
 out of 
5
(1 Review) 1
Open Ratings Snapshot
Rating Summary (1 review)
5 stars
0
4 stars
1
3 stars
0
2 stars
0
1 star
0
1 of 1(100%)would recommend this product to a friend.
Customer Reviews for "Please see replacement item# 48643. FREE SHIPPING - Hobart AirForce 700i Plasma Cutter - 230V, 40 Amps, Model #500546"
Review 1 for "Please see replacement item# 48643. FREE SHIPPING - Hobart AirForce 700i Plasma Cutter - 230V, 40 Amps, Model #500546"
Overall Rating:
4 / 5
4 / 5

Plasma Cutter

,
November 22, 2010
By
from Seattle, WA
Everything is excellant about the plasma cutting except the sliding trigger is hard to start. You have to slide the yellow safety device down while trying to pull the trigger. It's hard to do with one hand. Other than that it cuts good and I was glad I bought it.
Describe Yourself: Professional
+21points
23out of 25found this review helpful.